|
HERCULINER is the first nationally-marketed
do-it-yourself brush-on bed liner kit and has found
its success by offering a unique high quality
product. HERCULINER has built strong brand
recognition as the premium bed liner and has raised
awareness for the category among off road users.
HERCULINER is the only polyurethane and rubber
granule coating that is applied to the bed surface
using the rollers and brush included with the kit.
When cured, HERCULINER provides a durable
skid-resistant protective coating. Because it can
bond to virtually
any
surface or material, HERCULINER can be applied to
wood, metal, concrete, aluminum, asphalt, rubber,
fiberglass, and most plastics, including PVC.
When using the HERCULINER product there are an
endless amount of uses:
See text instructions on how to
install HERCULINER
here.
See online movie of
HERCULINER install here.
HERCULINER Question & Answer:
Q:
What is the material used in HERCULINER?
A:
HERCULINER is a mixture of polyurethane coating
with rubber granules to provide a
tough, textured finish.
Q:
How can it be applied?
A:
HERCULINER can be applied with a brush/roller or
with a spray compressor. (Brush and two (2)
rollers are included with each kit.) It must be
applied in a well ventilated area.
Q:
What colors are available?
A:
Black, Gray & Red
Q:
How much is the cost and in what size
containers will it be available?
A:
Suggested retail on the black kit is $99.99,
which includes one (1) gallon. Additional black
quarts are available for $29.99. Red & gray kits
are available for $139.99. Red & gray quarts are
available for $39.99.
Q:
What surfaces will it bond to?
A:
HERCULINER will bond to most clean/dry surfaces,
including painted or primed steel. Prepping the
surface is critical for best results;
instructions are included with the kit, or you
can just click on "Instructions" icon on this or
any other page of the HERCULINER site.
Q:
What is the shelf life of HERCULINER?
A:
If unopened, HERCULINER can be stored for
several years.
Q:
How tough is HERCULINER?
A:
HERCULINER won’t chip, flake or peel and is
resistant to damage from gasoline and most
chemicals
& solvents. It can withstand years of
heavy duty use.
Q:
How can I remove HERCULINER once it's
applied?
A:
You can use Xylene while product is still wet,
but if it dries, it's permanent.
Q:
What happens if I get HERCULINER on my
hands?
A:
Clean off immediately with Xylene, then wash
hands with soap and water.
Q:
How long does it take HERCULINER to dry?
A:
You should allow HERCULINER to dry about 9-12
hours before any light use and allow 24 hours
for a complete cure. Curing begins when
HERCULINER is exposed to atmospheric moisture.
Therefore, with higher humidity, curing time is
shorter.
Q:
How thick should it be applied?
A:
First coat forms a good base. After 1 hour to 1
½ hours to dry; then apply a second coat that
will cover any open pores. One (1) gallon covers
6’ beds with 2 coats; an extra quart is needed
for 8’ beds.
Q:
Can you repair a section that has been
damaged?
A:
Yes, HERCULINER adheres to itself, while other
coatings do not and would have to be removed for
gouging repair.
Q:
Is HERCULINER flammable?
A:
Yes, but after drying, it is no longer
flammable.
Q:
Can I apply HERCULINER in the winter?
A:
Yes, HERCULINER can be applied between 32° F and
95° F. However, the colder the temperature and
the lower the humidity, the longer the curing
process will take. Additionally, it
MUST BE APPLIED IN A WELL
VENTILATED AREA.
Q:
What is the difference between our
coating formula versus the other spray-on
coatings out there?
A:
HERCULINER has a proprietary polyurethane and
rubber formula. HERCULINER is the only
do-it-yourself bedliner with a tough, thick,
skid-resistant finish that won’t chip, flake or
peel.
Q:
What is included in a kit?
A:
1 gallon of protective coating
2 rollers for easy application
1 abrasive pad for scuffing/prepping bed
1 roller handle
1 gallon can opener
1 - 2" brush for tight spots/corners
Plus: Bed liner application instructions
in English, French, and Spanish AND application
instructions for other uses (also in English,
French, and Spanish).
Q:
What is not included in a kit that will
be needed to do the job right?
A:
One Quart of Xylene, Acetone or MEK (solution to
prep the surface of the bed before coating)
Rubber gloves
Stir stick (We recommend a drill with a
paint mixing attachment.)
Paint tray and some rags
Tape for masking off areas
Q:
What kind of warranty does HERCULINER
have?
A:
We warranty the product against faulty
manufacture and defective materials. We cannot
accept liability for application or use of this
product (too many variables, proper
prepping/cleaning of surface, application
methods, etc.).
Q:
What is the average cost for a dealer
installed spray-on bed liner?
A:
There are a number of different products and
dealers offering bed liner spray-on services.
Finished product mil thickness, skid resistant
properties, and costs vary by location from
$300.00 to over $500.00
Q:
Can I use HERCULINER Coating for other
uses?
A:
Yes, the HERCULINER Coating can be used on an
array of surfaces from concrete to plastic as
well as an undercoating to ramp coatings, etc.
Just click on the "Instructions" icon on this
page.
|
or Contact 
